| RT 42 Self Propelled Tunnel Maintenance Scaffold Rail Car | ||
|
» Application: used for track installation and general maintenance » Length: Variable 58.7 ft overall » Width: 10.3 ft overall » Height: 11.5 ft » Weight: Tare 80,000 lbs Gross 120,000 lbs » Scaffold: The scaffold consists of (7) removable modules. Two power modules are located at the front and rear with ladder access and a walkway door. The five (5) modules in between are identical. |
|
| Rail Maintenance-of-Way Equipment | ||
| RT 48 Multi-Purpose Self Propelled Rail Vehicle with Snow Thrower and Brush Blower Attachments | ||
|
» Application: Rail Tow Car, Track Snow Removal Attachments » Length x Width x Height: 18.3 ft x 10.3 ft x 10.7 overall » Weight: 34,000 lbs with Snow Thrower and Snow Blower/Brush Attachments » Cab: Enclosed Cab with two seats facing opposite directions as the machines may travel either direction. » Main Frame: Fabricated main frame is attached to the H1 truck at the bolster mount cap screws. Horizontal thrust is absorbed by packer plates between heavy vertical plates onto which the snow blower or brush blower are attached. The undercarriage is configured to accept the brush snow blower or tow/push coupler at either end. » Glycol System: The snow thrower unit is equipped with a system designed to spray glycol onto the power rail After the brushes and air nozzles have cleared snow from between the power rail cover and the power rail. |
|
| RT 56 Vacuum-Rodding Work Car | ||
|
» Used for sewer cleaning and water blasting in the subway system » Vacuum system will be utilized for the collection of track ballast from around rail ties » Length: 65 ft overall » Width: 10.3 ft overall » Height: 12 ft » Weight: Maximum 140,000 lbs |
|
| RT 17 Self-Propelled Tunnel Wash Car | ||
|
» Application, used to wash down subway tunnels and recover contaminated waste water » Length: 55 ft » Width: 9.4 ft » Height: 10.3 ft » Tare weight 84,000 lbs gross weight 120,000 lbs » Power, Detroit diesel 400 hp @ 1800 rpm |
|
| RT 57 General Purpose Rail Flat Car | ||
|
» Length: 55 ft overall » Width: 10.3 ft overall » Height: 3.6 ft » Weight: Tare 38,250 lbs Gross 86,250 lbs » Truck Make: Dofasco H1 » Truck Centre: 34.5 ft » Air System: WABCO » Brake: PEACOCK |
|
| Tri-Mode Work Car Locomotive | ||
|
» Application: fast deployment and recovery of rail cars » Tri-Mode Power includes Diesel-Electric, Third Rail, Battery Power » Dual Cab Configuration » Length: 55 ft » Width: 11.9 ft » Propulsion: Switch Reluctance Traction Motors and Drivers » Controls: Main control functions handled by ICAM system » Air and Brake System: Wabco » Fire Suppression System |
|
| ARA0309 Hydraulic Crane | ||
|
» Capacity: 14,000 lbs @ 12 ft and 6500 lbs @ 29 ft radius » Boom: 10 ft to 30 ft 4 section full power » Boom Elevation: -20 to 60 degrees » Length: 10ft 4in. retracted permits 180 degree swing within car width » Overall Width: 3 ft » Overall Height: 6 ft boom horizontal from car deck » Weight: 7,560 lbs » Outriggers: Out and down with 13 ft 10 in spread » 360 degrees continuous rotation » OSHA, ANSI and SAE Compliant |
|
| ARA0208 Hydraulic Crane | ||
|
» Capacity: 1500 lbs @ 29 ft radius » Boom: 10 ft to 30 ft 4 section full power » Boom Elevation: -20 to 60 degrees » Length: 10ft 4in. retracted permits 180 degree swing within car width » Overall Width: 3 ft » Overall Height: 6 ft boom horizontal from car deck » Weight: 4,050 lbs » 360 degrees continuous rotation » OSHA, ANSI and SAE Compliant |
|
| AR0101 Removable 1 ton Rail Crane | ||
|
» Capacity: 2000 lbs @ 8 ft radius » Boom: 5.5 ft to 8.5 ft 2 section full power » Boom Elevation: -30 to 50 degrees » Length: 6 ft 2in » Overall Height: 3.5 ft boom horizontal from car deck » Weight: 450 lbs » 320 degrees rotation » OSHA, ANSI and SAE Compliant |
|
| Anchor Bolt Drilling Attachment | ||
|
» Replaces defective bolts that secure the rails to the concrete ties » Capacity: 800 lbs vertical force to full extension » Reach: 98 inches centre of rotation to centre of drill » Telescopic: Hydraulically actuated with double acting cylinder » Drill Stroke: 18 inches from upper position which is 2 inches above track » Drill Post: drill post rack to mate with existing drill feed pinion » 140 degrees rotation from stowed position with disc-caliper type and mechanical lock » Controls: Two section manual control valve 1st section telescope, 2nd section swing function » Powered by existing fixed displacement pump with rated pressure of 2500 psi » OSHA, ANSI and SAE Compliant |
|
